跳至主要内容

What should be paid attention to when the excavator works in the rain?

 

1. Work on rainy days must pay attention to the conditions of the road surface, especially in places with particularly thick soil. After heavy rain, the soil is wet and wet, especially slippery. Work in these places must pay attention to the surrounding environment and always pay attention Observe that you can use a small throttle to work when pushing materials.

mining excavator


2. When the small hydraulic wheel excavator is used as a tractor in the rainy season, it must ensure the safety of the excavator. Only when you guarantee your own safety can you rescue others, especially when you are driving on the slope, you must see the road surface clearly. If there are too many It is best to remove the mud first, and if possible, shovel some sand and the like onto the road. This can greatly reduce the skidding of the vehicle. Rescue under the condition of ensuring safety must not be exhausted.


electric excavator


3. Avoid the small wheel excavator being too close to the cliff or the edge of the ditch. If the ground is soft in these places, it is easy to fall or tip over due to the weight and vibration of the excavator.

pokland machine

评论

此博客中的热门博文

Introduction of Compactor Garbage Truck

  The   compactor garbage truck   is composed of a sealed garbage hopper, a hydraulic system and an operating system. The whole truck is a fully sealed type, and the sewage in the process of self-compression, self-dumping and compression all enters the sewage tank, which completely solves the problem of secondary pollution in the process of garbage transportation. It has the advantages of good performance, convenient operation and safety. Optional rear hanging bucket overturning mechanism or garbage bucket overturning mechanism. The outstanding features of the compactor garbage truck and other garbage trucks: 1. The garbage collection method is simple: change the dirty old appearance of garbage cans on the streets of the city, and prevent secondary pollution. 2. High compression ratio and large loading capacity: the maximum crushing pressure is 12 tons, and the loading capacity is equivalent to two and a half times that of the same ton of uncompressed waste. 3. Operation ...

How to Prevent Hydraulic Oil From Emulsifying On Concrete Mixer Truck?

The main cause of hydraulic oil emulsification on concrete mixer truck s is water in the hydraulic system, which is mixed with water after a long time. The removed hydraulic oil will form an emulsification of the hydraulic oil. We found that water enters the hydraulic system due to the following reasons: a. Working in a humid environment, the moisture in the air condenses due to the alternation of cold and heat, turning into water droplets and falling into the oil; b. The rainwater on the fuel tank seeps into the fuel tank due to the weak sealing of welding and connection parts; c.  Due to the damage of the pumping cylinder seal and the damage of the mixing motor, moisture is brought into the oil; d. Daily maintenance, cleaning, oil change, and maintenance process bring in moisture. To prevent the oil from emulsifying, we must first prevent moisture from entering the hydraulic system. When the car leaves the factory, the welding and connection parts must be manufactured in accord...

Installation Guide of Turbo Charger

Please install your turbochargers according to our following installation guide in order to avoid some unnecessary damages. *Pre-Installation 1. Change new recommended quality oil & air filters. 2. Change recommended engine oil. 3. Pre-oil the turbo oil inlet. 4. Change new oil inlet pipes or flush the oil inlet pipes to remove flakes or carbon deposits. 5. Ensure oil supply of at least 0.5kgf/m2 or 7 psi within 3 seconds 1st engine start (if possible, use oil gauge to measure). 6. Mount turbine inlet to engine manifold 7. Attach oil inlet pipe to turbo and crank the engine a few times until oil flows out of the turbo oil drain. Then attach the oil drain pipe. 8. Connect remaining air piping hose. 9. Ensure that all bolts, screws & nuts are tightened. 10. Allow engine to idle for 5 minutes before operating at higher rpm. 11. Check for unusual noises and leaks 12. Do not operate the turbo if you suspect any problems. Consult us immediately. ...