Turck & Car center

Steel rings, also known as hubs, are an important part of semi-trailers . The “hub” and “tire” are two completely different parts. The so-called "tire" is the rubber part of the trailer, which is itself soft, so the inner profile of the tire supports the drum, and the center is the wheel mounted on the shaft. Maintenance method of steel ring: 1. When the temperature of the steel ring is high, it should be allowed to cool after it is naturally cooled. Never use cold water to clean it. Otherwise, the aluminum alloy steel ring will be damaged, and even the brake disk will be deformed to affect the braking effect. In addition, cleaning the steel ring with a cleaning agent at a high temperature causes a chemical reaction on the surface of the steel ring, which loses luster and affects the appearance. 2. When the steel ring is covered with hard-to-clear tar, if the general cleaning agent does not help, try to remove it with a brush, but do not use a hard brush, especially an ...

First of all, when customers choose the chassis, they are generally considered according to economic benefits, such as: chassis price, loading quality, overload capacity, fuel consumption per 100 kilometers, road maintenance fees, etc. In addition, for the safe driving requirements, the user should also consider the following parameters of the vehicle: 1. The height of the plane above the chassis frame is off the ground. In the industry, the height of the plane on the 6x4 chassis frame is generally 1200mm. The larger the value, the higher the center of gravity of the vehicle, and the more likely it is to cause a rollover. The factors affecting this value are mainly the tire diameter, the suspension arrangement and the height of the main frame section. Taking into account the normal use of customers, the industry is generally equipped with 12.00R20 radial tires, CLVEHICLES.COM through the continuous optimization of the suspension, frame, reduce the center of gravity of the vehicle,...

Refone can supply the following popular  turbochargers for Toyota .These models are in great demand especially in Africa. If have interests,please contact us.

Please install your turbochargers according to our following installation guide in order to avoid some unnecessary damages. *Pre-Installation 1. Change new recommended quality oil & air filters. 2. Change recommended engine oil. 3. Pre-oil the turbo oil inlet. 4. Change new oil inlet pipes or flush the oil inlet pipes to remove flakes or carbon deposits. 5. Ensure oil supply of at least 0.5kgf/m2 or 7 psi within 3 seconds 1st engine start (if possible, use oil gauge to measure). 6. Mount turbine inlet to engine manifold 7. Attach oil inlet pipe to turbo and crank the engine a few times until oil flows out of the turbo oil drain. Then attach the oil drain pipe. 8. Connect remaining air piping hose. 9. Ensure that all bolts, screws & nuts are tightened. 10. Allow engine to idle for 5 minutes before operating at higher rpm. 11. Check for unusual noises and leaks 12. Do not operate the turbo if you suspect any problems. Consult us immediately. ...

Refone have some new developing models turbocharger for Renault, please checking information as below. BV38 5438-988-0002 for Renault Scenic III Dacia Duster 1.5L dCi K9K EURO 6 Engine BV38 5438-970-0001/0007/0017 for Renault Megane III with R9M Engine We also can provide more turbo parts replacement of this two models. Welcome you to inquiry us.

At present, Billet/MFS compressor wheels are popular trend in the turbocharger industry. Many performance turbos and new electronic turbos use MFS/Billet compressor wheels to improve the performance and working intensity of turbochargers . Compared with traditional cast compressor wheel, they are both made from aluminum material. The machining technology is different: common compressor wheel are casted in aluminum water, so the density is low; Billet/MFS Wheel is machined from solid aluminum compressor wheel and is carved from a complete piece of aluminum, which has a higher density and strength, which greatly improves service life and power. Moreover, There are many billet compressor wheel with various colors, red, blue, yellow, etc. have appeared on the market, which greatly enhances the viewing of the turbocharger and is very suitable for brand publicity.

Based on request from customers and market,Refone can provide MFS billet compressor wheel for cartridges and turbos . Below are Refone new developing chras with MFS billet wheel . Welcome to check and contact us for prices,more turbo billet wheels for your need.

The Italy brand ET tester , which is very easy to operate, can test various Hella REA and S-REA electronic actuators and other 12v electronic actuators of Toyota, VW, Mistubishi turbos and etc. The ET tester includes 19 cables to connect with different electronic actuators’ plug. It also offer a brochure to instruct how you use the tester. For better understanding, please refer to a video below. If you want to know more about the ET tester price and want to receive a catalog of electronic turbo actuators what can be tested on the ET, contact us at any time.